Kits

QRP Labs
17-inch DELL Computer Monitor recyling! PDF Print E-mail
Written by Hans Summers   
Saturday, 01 January 2011 17:02

Don't throw away your old computer monitor! Inside there are numerous parts to restock your junk box. Scroll down to see what useful components I found in a 17-inch DELL multisync monitor, and photographs of the dismantling process.

WARNING!

Take care when recycling monitors:

1) do not break the fragile glass neck of the Cathode Ray Tube
2) make sure the unit has been switched off for some time to allow the internal high voltage capacitors to discharge.
3) Of course, watch out for sharp metal etc.
4) Recycling old electronics is ADDICTIVE!

"John K" who emailed me with further warnings about dismantling monitors and televisions. CRT's can store a high voltage charge, due to their behaviour as a capacitor (metalised coating inside and outside the glass). The danger is the EHT connection which you can normally find by looking for a thick wire going to a rubbery pad on the body of the CRT. Unfortunately, even if the "capacitor" is shorted out, within minutes a charge can rebuild by itself, via a process called "dielectric hysteresis", or "dielectric soak". The electric shock one might receive would be unpleasant but would likely do less damage than the probability of then dropping the CRT, which may then implode on impact causing flying glass injuries etc. John says: "many servicemen prefer to break the exhaust pip on the tube to let the air in. Said to be safer than risking the chance of an implosion". Personally I have dismantled many TV's and monitors in my life and never suffered shock or explosion. I suppose I generally cut the thick cable, extract the CRT then leave it alone, so haven't touched the wires. Still, this warning is good advice, definitely something to be aware of. More information on the dielectric hysteresis affect can be found at: http://www.siteswithstyle.com/VoltSecond/ and http://www.faradnet.com/glossary/d_gloss.htm#da .

Inventory of useful parts

I will keep the PCB's and other parts in my junk box, and unsolder components as and when I find the need for them.

Integrated Circuits:

LM324 Quad Operational Amplifier (SMD)
KA358 Dual operational Amplifier
74HCF4011 Quad 2-input NAND gate (SMD)
74HCT02 Quad 2-input NOR gate (SMD)
74HC86 Quad 2-input XOR gate (SMD)
74HCT74 Dual D-type Flip Flop (SMD)
74HCF4053 Tripple 2-channel multiplexer (SMD)
UC3842 Current mode PWM controller
TDA9105 Deflection processor
LM1283 140MHz RGB Video Amplifier
MAS9181 Eight discrete 8-bit Digital-Analogue converters in one IC, I2C programmed
CVA4401 Triple 400MHz buffer
CR6727 Triple hybrid video amplifier
LM2940 12V 1A Voltage Regulator
7805 5V 1A Voltage Regulator
Several other custom IC's which I couldn't find datasheets for on the internet

Other semiconductors:

SLA5038 5-MOSFET array
Several LARGE rectifier diodes
Several zener diodes
Numerous small signal diodes, look like 1N4148, both SMD and normal
Numerous small transistors, both SMD and normal
Several IRF-series TO220 MOSFET's, e.g. IRF620
Several BD-series bipolar power transistors e.g. BD135
5mm green LED

Other components:

Numerous resistors, both SMD and normal, various power ratings
Numerous capacitors, both SMD and normal, including many useful electrolytics
Notable LARGE 330uF 385V smoothing capacitor in the mains rectifier
Two small neon bulbs, used as spark gaps
8MHz quartz crystal, HC49 case
Numerous inductors and transformers, but no toroids
12V Relay, dual pole changeover
Numerous preset potentiometers
Five small push buttons
Approx 10 metres of shielded cable, i.e. 5 shielded conductors in the cable

NOTE ALSO: Barry Smith writes: "Another part of some monitors, and most TVs, is that squarish cone of metal covering the back of the CRT. I think its a mu-metal magnetic shield. Might be worth saving. At least, that's what I tell myself."

Photographs

Click the images for larger version of the photographs.

Left: If you do this on your desk at the office, people are going to ask questions...
Centre: Inside the monitor case, was a secondary box made of thin sheet metal: for RF screening purposes.
Right: The driver PCB came off first. It has a socket which was plugged directly to the end of the Cathode Ray Tube.


Left: Next I removed the deflection coils. These are supposed to create a magnetic field which directs the electron beam across the face of the screen. I have seen these coil yolks before in televisions, consisting of just two coils (horizontal and vertical deflection). Not here! This one has two main coils, but all manner of auxilliary coils mounted at various angles.
Centre: The main PCB is large and loaded with useful components. That's my shoe on the left of the picture.
Right: The reverse side of the PCB. The removable plastic shield covers the high voltage areas. This side of the board is covered in surface mount components, including several useful IC's.


Left: This small board fits in the front panel of the monitor, for user adjustment. It contains 5 buttons and one 5mm green LED.
Centre: At the top and bottom of the cathode ray tube, just inside the front panel, were mounted these two large loops!
Thanks to Ray Redbourne for emailing me some further information: these are "degaussing coils", and are energised briefly at switch-in in order to remove any residual magnetism in the CRT.
Right: Peeling away the plastic tape it became clear that they are coiled enamalled wire. Very useful indeed, in a perfect storable form, and easy-to-use later without having to unwind from transformers etc.!


The Sony 17-inch Trinitron tube. Destined for the rubbish dump.

Last Updated on Saturday, 01 January 2011 17:20
 
© 2009-2024 Hans Summers
Web services by DataState Solutions